{"id":8400,"date":"2026-10-23T10:33:14","date_gmt":"2026-10-23T10:33:14","guid":{"rendered":"https:\/\/www.lyafs.com\/?p=8400"},"modified":"2026-10-23T10:33:14","modified_gmt":"2026-10-23T10:33:14","slug":"sand-mold-core-printing-buyers-checklist","status":"publish","type":"post","link":"https:\/\/www.lyafs.com\/tr\/blog\/sand-mold-core-printing-buyers-checklist\/","title":{"rendered":"Sand Mold and Core Printing: A Buyer&#8217;s Checklist"},"content":{"rendered":"\n<p class=\"wp-block-paragraph\">Buying sand mold and core printing is two decisions, not one: whether to buy a machine or buy printed molds as a service, and if you buy, which specification actually matters. Six questions decide it \u2014 annual mold volume, largest core, tolerance on the functional faces, sand and binder system, post-processing capacity, and who owns process development. Get those wrong and the machine will sit idle regardless of its build volume.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Key takeaways<\/h2>\n\n\n\n<ul class=\"wp-block-list\"><li>The largest <strong>core<\/strong> usually sets the machine size, not the largest mold \u2014 cores are the constraint people discover too late.<\/li>\n<li>Throughput is measured in molds per shift, not litres per hour: cure and depowder time is part of the cycle.<\/li>\n<li>Binder choice follows the pouring temperature, and it is not freely interchangeable on a given machine.<\/li>\n<li>Post-processing \u2014 cure, depowder, coating, assembly \u2014 is roughly half the labour of a printed mold.<\/li>\n<li>Below about 20 molds a month, buying printed molds as a service almost always beats owning a machine.<\/li><\/ul>\n\n\n\n<h2 class=\"wp-block-heading\">The six questions that decide the answer<\/h2>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"wp-block-table\">\n<thead>\n<tr><th>#<\/th><th>Question<\/th><th>What it determines<\/th><th>Get it wrong and\u2026<\/th><\/tr>\n<\/thead>\n<tbody>\n<tr><td>1<\/td><td>How many molds a year, and how regular?<\/td><td>Machine versus service; one machine versus two<\/td><td>The machine is idle most of the year, or is the bottleneck every month<\/td><\/tr>\n<tr><td>2<\/td><td>What is the largest <strong>core<\/strong>, not the largest mold?<\/td><td>Build envelope, and therefore price class<\/td><td>You buy a machine that cannot print your cores<\/td><\/tr>\n<tr><td>3<\/td><td>What tolerance sits on the functional faces?<\/td><td>Whether as-printed is enough or machining is required<\/td><td>You budget for printing but pay for machining<\/td><\/tr>\n<tr><td>4<\/td><td>Which sand and which binder?<\/td><td>Alloy compatibility, gas evolution, sand reclamation<\/td><td>The binder cannot survive your pouring temperature<\/td><\/tr>\n<tr><td>5<\/td><td>Who does cure, depowder and coating?<\/td><td>Labour, floor space, throughput<\/td><td>Printing is fast, the rest of the line is not<\/td><\/tr>\n<tr><td>6<\/td><td>Who owns process development?<\/td><td>Time to first good mold, and after every alloy change<\/td><td>Every new alloy becomes a new qualification project<\/td><\/tr>\n<\/tbody>\n<\/table><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\">Build envelope: measure your largest core, not your largest mold<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">This is the mistake that is most expensive to fix. A foundry measures its largest casting, adds a margin, and specifies a build volume from that number. Then the first job arrives with a three-part core set, and the cores do not fit. The cycle-time and cost side of the same decision is covered in <a href=\"\/blog\/sand-3d-printing-vs-traditional-sand-casting\/\">printed molds versus traditional sand casting<\/a>.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">In a conventional foundry the core box is separate tooling, so its size is a separate line item. In a printed foundry the core and the mold come out of the same build volume \u2014 which means the <strong>core<\/strong> now has to fit, and cores can be awkward: tall, thin, and oriented in a way that wastes bed height.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"wp-block-table\">\n<thead>\n<tr><th>What you measure<\/th><th>Why it matters<\/th><th>Practical check<\/th><\/tr>\n<\/thead>\n<tbody>\n<tr><td>Largest core, including core prints<\/td><td>Cores often exceed the mold in one dimension<\/td><td>Measure the core box, not the pattern<\/td><\/tr>\n<tr><td>Core orientation in the build<\/td><td>Height drives print time more than volume does<\/td><td>Can the core lie down? If not, budget the height<\/td><\/tr>\n<tr><td>Number of cores per mold<\/td><td>All cores must fit in the same bed as the mold<\/td><td>Add every core to the footprint, not just the largest<\/td><\/tr>\n<tr><td>Mold wall thickness plus print allowance<\/td><td>The printed shell is thicker than the pattern<\/td><td>Add 20\u201330 mm around the casting envelope<\/td><\/tr>\n<\/tbody>\n<\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">A production machine in this class offers a 1,800 \u00d7 1,000 \u00d7 700 mm build volume and handles molds of 1.3 t or more. That envelope covers a large share of industrial castings \u2014 but it only helps if the cores fit inside it too.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Sand and binder system<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The sand and binder pair is not a consumable choice you can change freely after purchase. It determines which alloys you can pour, how much gas the mold evolves, and how much of the sand you can reclaim.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"wp-block-table\">\n<thead>\n<tr><th>Sand<\/th><th>Best for<\/th><th>Trade-off<\/th><\/tr>\n<\/thead>\n<tbody>\n<tr><td>Quartz (silica) sand<\/td><td>The default for iron, steel and aluminium<\/td><td>Cheapest and most available; thermal expansion at high temperature<\/td><\/tr>\n<tr><td>Ceramic sand<\/td><td>Steel and high-temperature alloys, heavy sections<\/td><td>Higher cost per tonne; better dimensional stability<\/td><\/tr>\n<tr><td>Chromite sand<\/td><td>Chill zones and hot spots<\/td><td>Heavy, expensive, usually used as a facing rather than the bulk<\/td><\/tr>\n<\/tbody>\n<\/table><\/figure>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"wp-block-table\">\n<thead>\n<tr><th>Binder<\/th><th>Pouring temperature<\/th><th>Gas evolution<\/th><th>Notes<\/th><\/tr>\n<\/thead>\n<tbody>\n<tr><td>Phenolic<\/td><td>Steel and iron, high temperature<\/td><td>Lower than furan in many formulations<\/td><td>The usual choice for ferrous work<\/td><\/tr>\n<tr><td>Furan<\/td><td>Aluminium and lower-temperature alloys<\/td><td>8\u201315 ml\/g at 850 \u00b0C in typical printed molds<\/td><td>Good strength, well understood in foundries<\/td><\/tr>\n<\/tbody>\n<\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Ask two questions on the spec sheet: which binders the machine is validated for, and what tensile strength the printed mold reaches. A printed mold in this class runs 1.5\u20132.5 MPa tensile \u2014 comparable to a well-rammed conventional mold, and the number you need in order to trust the mold with a heavy section.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Accuracy and surface finish you should expect<\/h2>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"wp-block-table\">\n<thead>\n<tr><th>Measure<\/th><th>Typical printed value<\/th><th>What it means in the casting<\/th><\/tr>\n<\/thead>\n<tbody>\n<tr><td>Dimensional accuracy<\/td><td>\u00b10.3 mm up to 300 mm; \u00b10.5 mm above<\/td><td>Well inside ISO 8062 DCTG 5\u20136 for most sizes<\/td><\/tr>\n<tr><td>Layer thickness<\/td><td>0.2\u20130.5 mm<\/td><td>Sets the as-cast surface texture; thinner is slower<\/td><\/tr>\n<tr><td>Minimum wall thickness<\/td><td>2\u20133 mm<\/td><td>Thinner than a pattern-and-draft route allows<\/td><\/tr>\n<tr><td>Repeatability<\/td><td>Same file, same mold, every build<\/td><td>No pattern wear, so no drift across a run<\/td><\/tr>\n<\/tbody>\n<\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">The practical consequence: layer lines transfer to the casting as a fine texture. For a machined or coated surface that is irrelevant. For a cosmetic as-cast surface it means either a mold coating or extra machining allowance \u2014 and that decision should be made before the first quote, not after the first casting.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Throughput: prints per shift, not prints per hour<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Print speed is quoted in seconds per layer, and it is the least useful number on the sheet by itself. What decides the schedule is how many complete molds leave the building per shift.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"wp-block-table\">\n<thead>\n<tr><th>Measure<\/th><th>Typical figure<\/th><th>How to use it<\/th><\/tr>\n<\/thead>\n<tbody>\n<tr><td>Print speed<\/td><td>18\u201325 seconds per layer<\/td><td>Multiply by layer count for build time<\/td><\/tr>\n<tr><td>Layer thickness<\/td><td>0.2\u20130.5 mm<\/td><td>A 700 mm tall job is 1,400\u20133,500 layers<\/td><\/tr>\n<tr><td>Volumetric throughput<\/td><td>up to 153 L\/h of mold<\/td><td>Use for comparing machines of different sizes<\/td><\/tr>\n<tr><td>Cure and depowder<\/td><td>Several hours<\/td><td>Add this before you count a mold as done<\/td><\/tr>\n<tr><td>Molds per shift<\/td><td>Derived, not quoted<\/td><td>This is the number to negotiate on<\/td><\/tr>\n<\/tbody>\n<\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Ask a supplier for molds per shift on <strong>your<\/strong> part, not on a demo cube. A tall core and a flat plate of the same volume can differ by a factor of three in build time, because layer-based processes are governed by height.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Post-processing is half the job<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Printing produces a green mold that is not yet ready to pour. The <a href=\"\/blog\/how-sand-3d-printing-works\/\">sand 3D printing process<\/a> covers how the mold is built; four steps follow it, and each one takes labour and floor space.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"wp-block-table\">\n<thead>\n<tr><th>Step<\/th><th>Why it exists<\/th><th>Cost driver<\/th><\/tr>\n<\/thead>\n<tbody>\n<tr><td>Cure<\/td><td>Binder must reach handling strength<\/td><td>Oven or rack time, floor space<\/td><\/tr>\n<tr><td>Depowder<\/td><td>Loose sand must leave every internal passage<\/td><td>Labour hours, the main manual step<\/td><\/tr>\n<tr><td>Coating<\/td><td>Controls surface finish and metal penetration<\/td><td>Consumables plus drying time<\/td><\/tr>\n<tr><td>Assembly and closing<\/td><td>Multiple cores set into the mold<\/td><td>Labour, and the tolerance that matters most<\/td><\/tr>\n<\/tbody>\n<\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Depowder is the step most often underestimated. A mold with long, narrow internal passages takes longer to clear than a simple open cavity, and that time does not appear in any print-speed figure.<\/p>\n\n\n\n<figure class=\"wp-block-image size-large\"><img decoding=\"async\" src=\"https:\/\/www.lyafs.com\/wp-content\/uploads\/2026\/08\/3DPTEK-J1800S.png\" alt=\"3DPTEK-J1800S sand 3D printer with modular printheads\"\/><figcaption class=\"wp-element-caption\">3DPTEK-J1800S \u2014 same 1,800 \u00d7 1,000 \u00d7 700 mm build volume as the J1800, four modular printheads, and about 7 t of machine instead of 13 t.<\/figcaption><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\">Buy the machine, or buy the parts?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">This decision comes before the specification. Two machines in this class differ mainly in throughput and footprint, not in capability \u2014 the J1800 runs eight printheads with up to 153 L\/h and weighs about 13 t; the J1800S runs four modular printheads, is slightly slower per layer, and weighs about 7 t with a lower floor-load requirement. Choosing between them is an afterthought if the volume does not justify owning either.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"wp-block-table\">\n<thead>\n<tr><th>Your situation<\/th><th>Better answer<\/th><th>Reason<\/th><\/tr>\n<\/thead>\n<tbody>\n<tr><td>Fewer than about 20 molds a month<\/td><td>Buy printed molds<\/td><td>Machine cost is fixed; service cost scales with output<\/td><\/tr>\n<tr><td>20\u201360 molds a month, regular<\/td><td>Marginal \u2014 model both<\/td><td>Depends on mold size and post-processing labour<\/td><\/tr>\n<tr><td>60+ molds a month<\/td><td>Own the machine<\/td><td>Throughput and lead-time control both improve<\/td><\/tr>\n<tr><td>Occasional very large casting<\/td><td>Buy printed molds<\/td><td>Envelope requirement would force an oversized machine<\/td><\/tr>\n<tr><td>Confidential or prototype work<\/td><td>Own the machine<\/td><td>Sending models out may not be acceptable<\/td><\/tr>\n<\/tbody>\n<\/table><\/figure>\n\n\n\n<h3 class=\"wp-block-heading\">When a service wins<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">A service wins when your geometry varies more than your volume does, when the largest core would force a machine class you cannot justify, or when you do not yet know whether the printed route fits your foundry at all. Printing one mold externally answers that question for the price of one mold.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">When ownership wins<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Ownership wins when printed molds become a routine part of production \u2014 not an experiment. At that point lead time stops being a purchase decision and becomes a scheduling one, and owning the machine moves it from a queue you do not control into one you do.<\/p>\n\n\n\n<figure class=\"wp-block-image size-large\"><img loading=\"lazy\" decoding=\"async\" src=\"https:\/\/www.lyafs.com\/wp-content\/uploads\/2026\/05\/3D-Printed-Engine-Block-sand-casting.jpg\" alt=\"3D printed sand mold and core set for an engine block casting\" width=\"800\" height=\"600\"\/><figcaption class=\"wp-element-caption\">An engine block mold and core set. Several cores print in one build \u2014 which is why the largest core, not the largest mold, sets the envelope.<\/figcaption><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\"><p><strong>Comparing a machine against buying printed molds?<\/strong> Send one of your molds and its core set \u2014 we will quote it as printed parts and tell you the volume at which owning a machine starts to win. <a href=\"\/services\/sand-mold-sand-core-3d-printing\/\">Sand mold and core printing service<\/a> \u00b7 <a href=\"\/services\/sand-casting\/\">Sand casting service<\/a> \u00b7 <a href=\"\/3d-printers\/sand-3d-printers\/\">Sand 3D printer range<\/a><\/p><\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Frequently asked questions<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\">What printer makes sand molds for casting?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Binder jetting sand printers. A printhead deposits binder into a bed of quartz or ceramic sand, building the mold and its cores layer by layer at 0.2\u20130.5 mm per layer. Production machines in this class offer 1,800 \u00d7 1,000 \u00d7 700 mm build volumes and handle molds of 1.3 t or more.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">How much does a sand 3D printer cost?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Sand 3D printers sit in the industrial range, well above polymer machines, because the build volume, sand handling and binder system all scale with the bed. A machine specification should be built from the largest core, the required molds per shift and the binder system for your alloys \u2014 the configuration drives the price far more than the model name.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Can you print cores as well as molds?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Yes, and that is the main structural advantage. Cores print in the same build as the mold, in one piece, with no core box and no core assembly. A part with five internal passages prints as a single mold-and-core set instead of a mold plus five separately made cores.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">What is the largest sand mold that can be printed?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Entry production machines handle 1,800 \u00d7 1,000 \u00d7 700 mm and molds of 1.3 t or more. Larger formats extend the envelope to several metres in the largest direction. The practical limit is usually the largest core that must fit alongside the mold, not the mold itself.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Do printed molds need coating?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Often, yes. A refractory coating controls metal penetration and improves the as-cast surface, especially where layer lines would otherwise show. Whether you need it depends on the alloy, the section thickness and whether the surface is cosmetic or machined.<\/p>\n\n\n\n<script type=\"application\/ld+json\">\n{\n  \"@context\": \"https:\/\/schema.org\",\n  \"@type\": \"FAQPage\",\n  \"mainEntity\": [\n    {\"@type\":\"Question\",\"name\":\"What printer makes sand molds for casting?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Binder jetting sand printers. A printhead deposits binder into a bed of quartz or ceramic sand, building the mold and its cores layer by layer at 0.2-0.5 mm per layer. Production machines in this class offer 1,800 x 1,000 x 700 mm build volumes and handle molds of 1.3 t or more.\"}},\n    {\"@type\":\"Question\",\"name\":\"How much does a sand 3D printer cost?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Sand 3D printers sit in the industrial range, well above polymer machines, because the build volume, sand handling and binder system all scale with the bed. The configuration drives the price far more than the model name.\"}},\n    {\"@type\":\"Question\",\"name\":\"Can you print cores as well as molds?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Yes, and that is the main structural advantage. Cores print in the same build as the mold, in one piece, with no core box and no core assembly. A part with five internal passages prints as a single mold-and-core set.\"}},\n    {\"@type\":\"Question\",\"name\":\"What is the largest sand mold that can be printed?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Entry production machines handle 1,800 x 1,000 x 700 mm and molds of 1.3 t or more. Larger formats extend the envelope to several metres in the largest direction. The practical limit is usually the largest core that must fit alongside the mold.\"}},\n    {\"@type\":\"Question\",\"name\":\"Do printed molds need coating?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Often, yes. A refractory coating controls metal penetration and improves the as-cast surface, especially where layer lines would otherwise show. Whether you need it depends on the alloy, the section thickness and whether the surface is cosmetic or machined.\"}}\n  ]\n}\n<\/script>\n","protected":false},"excerpt":{"rendered":"<p>A buyer&#8217;s checklist for sand mold and core printing &#8211; build envelope, sand and binder, accuracy, throughput per shift, post-processing, and machine versus service.<\/p>","protected":false},"author":1,"featured_media":5849,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_oxygen_hide_in_design_set":false,"_oxygen_tags":"","footnotes":""},"categories":[4],"tags":[20,9,5],"class_list":["post-8400","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-sand-3d-printing","tag-buyers-guide","tag-patternless-casting","tag-sand-3d-printer"],"yoast_head":"<title>Sand Mold and Core Printing: Buyer&#039;s Checklist<\/title>\n<meta name=\"description\" content=\"Six questions decide a sand mold and core printing purchase: volume, largest core, tolerance, sand and binder, post-processing capacity, and process ownership.\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/www.lyafs.com\/tr\/blog\/sand-mold-core-printing-buyers-checklist\/\" \/>\n<meta property=\"og:locale\" content=\"tr_TR\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"Sand Mold and Core Printing: Buyer&#039;s Checklist\" \/>\n<meta property=\"og:description\" content=\"Six questions decide a sand mold and core printing purchase: volume, largest core, tolerance, sand and binder, post-processing capacity, and process ownership.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/www.lyafs.com\/tr\/blog\/sand-mold-core-printing-buyers-checklist\/\" \/>\n<meta property=\"og:site_name\" content=\"3DPTEK | AFS\" \/>\n<meta property=\"article:author\" content=\"https:\/\/www.facebook.com\/profile.php?id=100093519070922\" \/>\n<meta property=\"article:published_time\" content=\"2026-10-23T10:33:14+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/www.lyafs.com\/wp-content\/uploads\/2026\/05\/Industrial-Sand-3D-Printer-in-Foundry-1024x768-1.jpg\" \/>\n\t<meta property=\"og:image:width\" content=\"1024\" \/>\n\t<meta property=\"og:image:height\" content=\"768\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/jpeg\" \/>\n<meta name=\"author\" content=\"Jeff\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Yazan:\" \/>\n\t<meta name=\"twitter:data1\" content=\"Jeff\" \/>\n\t<meta name=\"twitter:label2\" content=\"Tahmini okuma s\u00fcresi\" \/>\n\t<meta name=\"twitter:data2\" content=\"9 dakika\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\\\/\\\/schema.org\",\"@graph\":[{\"@type\":\"Article\",\"@id\":\"https:\\\/\\\/www.lyafs.com\\\/tr\\\/blog\\\/sand-mold-core-printing-buyers-checklist\\\/#article\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/www.lyafs.com\\\/tr\\\/blog\\\/sand-mold-core-printing-buyers-checklist\\\/\"},\"author\":{\"name\":\"Jeff\",\"@id\":\"https:\\\/\\\/www.lyafs.com\\\/ja\\\/#\\\/schema\\\/person\\\/0a46696ff959c86c3758ad7590adf5c3\"},\"headline\":\"Sand Mold and Core Printing: A Buyer&#8217;s Checklist\",\"datePublished\":\"2026-10-23T10:33:14+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\\\/\\\/www.lyafs.com\\\/tr\\\/blog\\\/sand-mold-core-printing-buyers-checklist\\\/\"},\"wordCount\":1812,\"publisher\":{\"@id\":\"https:\\\/\\\/www.lyafs.com\\\/ja\\\/#organization\"},\"image\":{\"@id\":\"https:\\\/\\\/www.lyafs.com\\\/tr\\\/blog\\\/sand-mold-core-printing-buyers-checklist\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/www.lyafs.com\\\/wp-content\\\/uploads\\\/2026\\\/05\\\/Industrial-Sand-3D-Printer-in-Foundry-1024x768-1.jpg\",\"keywords\":[\"Buyer's Guide\",\"Patternless Casting\",\"Sand 3D Printer\"],\"articleSection\":[\"Sand 3D Printing\"],\"inLanguage\":\"tr\"},{\"@type\":\"WebPage\",\"@id\":\"https:\\\/\\\/www.lyafs.com\\\/tr\\\/blog\\\/sand-mold-core-printing-buyers-checklist\\\/\",\"url\":\"https:\\\/\\\/www.lyafs.com\\\/tr\\\/blog\\\/sand-mold-core-printing-buyers-checklist\\\/\",\"name\":\"Sand Mold and Core Printing: Buyer's Checklist\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/www.lyafs.com\\\/ja\\\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\\\/\\\/www.lyafs.com\\\/tr\\\/blog\\\/sand-mold-core-printing-buyers-checklist\\\/#primaryimage\"},\"image\":{\"@id\":\"https:\\\/\\\/www.lyafs.com\\\/tr\\\/blog\\\/sand-mold-core-printing-buyers-checklist\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/www.lyafs.com\\\/wp-content\\\/uploads\\\/2026\\\/05\\\/Industrial-Sand-3D-Printer-in-Foundry-1024x768-1.jpg\",\"datePublished\":\"2026-10-23T10:33:14+00:00\",\"description\":\"Six questions decide a sand mold and core printing purchase: volume, largest core, tolerance, sand and binder, post-processing capacity, and process ownership.\",\"breadcrumb\":{\"@id\":\"https:\\\/\\\/www.lyafs.com\\\/tr\\\/blog\\\/sand-mold-core-printing-buyers-checklist\\\/#breadcrumb\"},\"inLanguage\":\"tr\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\\\/\\\/www.lyafs.com\\\/tr\\\/blog\\\/sand-mold-core-printing-buyers-checklist\\\/\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"tr\",\"@id\":\"https:\\\/\\\/www.lyafs.com\\\/tr\\\/blog\\\/sand-mold-core-printing-buyers-checklist\\\/#primaryimage\",\"url\":\"https:\\\/\\\/www.lyafs.com\\\/wp-content\\\/uploads\\\/2026\\\/05\\\/Industrial-Sand-3D-Printer-in-Foundry-1024x768-1.jpg\",\"contentUrl\":\"https:\\\/\\\/www.lyafs.com\\\/wp-content\\\/uploads\\\/2026\\\/05\\\/Industrial-Sand-3D-Printer-in-Foundry-1024x768-1.jpg\",\"width\":1024,\"height\":768,\"caption\":\"Industrial sand 3D printer producing a mold in a foundry\"},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\\\/\\\/www.lyafs.com\\\/tr\\\/blog\\\/sand-mold-core-printing-buyers-checklist\\\/#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\\\/\\\/www.lyafs.com\\\/tr\\\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Sand Mold and Core Printing: A Buyer&#8217;s Checklist\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\\\/\\\/www.lyafs.com\\\/ja\\\/#website\",\"url\":\"https:\\\/\\\/www.lyafs.com\\\/ja\\\/\",\"name\":\"3DPTEK | AFS\",\"description\":\"Renowned Chinese Industrial-Grade 3D Printing &amp; Rapid-Casting Solutions Provider\",\"publisher\":{\"@id\":\"https:\\\/\\\/www.lyafs.com\\\/ja\\\/#organization\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\\\/\\\/www.lyafs.com\\\/ja\\\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"tr\"},{\"@type\":\"Organization\",\"@id\":\"https:\\\/\\\/www.lyafs.com\\\/ja\\\/#organization\",\"name\":\"3DPTEK (3D Printing Technology Inc.)\",\"url\":\"https:\\\/\\\/www.lyafs.com\\\/ja\\\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"tr\",\"@id\":\"https:\\\/\\\/www.lyafs.com\\\/ja\\\/#\\\/schema\\\/logo\\\/image\\\/\",\"url\":\"https:\\\/\\\/lyafs.com\\\/wp-content\\\/uploads\\\/2026\\\/08\\\/logo-34.png\",\"contentUrl\":\"https:\\\/\\\/lyafs.com\\\/wp-content\\\/uploads\\\/2026\\\/08\\\/logo-34.png\",\"width\":232,\"height\":34,\"caption\":\"3DPTEK (3D Printing Technology Inc.)\"},\"image\":{\"@id\":\"https:\\\/\\\/www.lyafs.com\\\/ja\\\/#\\\/schema\\\/logo\\\/image\\\/\"}},{\"@type\":\"Person\",\"@id\":\"https:\\\/\\\/www.lyafs.com\\\/ja\\\/#\\\/schema\\\/person\\\/0a46696ff959c86c3758ad7590adf5c3\",\"name\":\"Jeff\",\"image\":{\"@type\":\"ImageObject\",\"inLanguage\":\"tr\",\"@id\":\"https:\\\/\\\/www.lyafs.com\\\/wp-content\\\/uploads\\\/2026\\\/09\\\/Jeff-150x150.jpg\",\"url\":\"https:\\\/\\\/www.lyafs.com\\\/wp-content\\\/uploads\\\/2026\\\/09\\\/Jeff-150x150.jpg\",\"contentUrl\":\"https:\\\/\\\/www.lyafs.com\\\/wp-content\\\/uploads\\\/2026\\\/09\\\/Jeff-150x150.jpg\",\"caption\":\"Jeff\"},\"description\":\"With 30+ years of additive manufacturing experience and 25+ sand 3D printers running in our own facilities, the 3DPTEK engineering team writes from hands-on production experience \u2014 not theory. We operate what we sell.\",\"sameAs\":[\"https:\\\/\\\/www.lyafs.com\",\"https:\\\/\\\/www.facebook.com\\\/profile.php?id=100093519070922\",\"https:\\\/\\\/www.linkedin.com\\\/in\\\/jeff-wei-56812b244\\\/\"],\"url\":\"https:\\\/\\\/www.lyafs.com\\\/tr\\\/blog\\\/author\\\/test\\\/\"}]}<\/script>","yoast_head_json":{"title":"Sand Mold and Core Printing: Buyer's Checklist","description":"Six questions decide a sand mold and core printing purchase: volume, largest core, tolerance, sand and binder, post-processing capacity, and process ownership.","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/www.lyafs.com\/tr\/blog\/sand-mold-core-printing-buyers-checklist\/","og_locale":"tr_TR","og_type":"article","og_title":"Sand Mold and Core Printing: Buyer's Checklist","og_description":"Six questions decide a sand mold and core printing purchase: volume, largest core, tolerance, sand and binder, post-processing capacity, and process ownership.","og_url":"https:\/\/www.lyafs.com\/tr\/blog\/sand-mold-core-printing-buyers-checklist\/","og_site_name":"3DPTEK | AFS","article_author":"https:\/\/www.facebook.com\/profile.php?id=100093519070922","article_published_time":"2026-10-23T10:33:14+00:00","og_image":[{"width":1024,"height":768,"url":"https:\/\/www.lyafs.com\/wp-content\/uploads\/2026\/05\/Industrial-Sand-3D-Printer-in-Foundry-1024x768-1.jpg","type":"image\/jpeg"}],"author":"Jeff","twitter_card":"summary_large_image","twitter_misc":{"Yazan:":"Jeff","Tahmini okuma s\u00fcresi":"9 dakika"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"Article","@id":"https:\/\/www.lyafs.com\/tr\/blog\/sand-mold-core-printing-buyers-checklist\/#article","isPartOf":{"@id":"https:\/\/www.lyafs.com\/tr\/blog\/sand-mold-core-printing-buyers-checklist\/"},"author":{"name":"Jeff","@id":"https:\/\/www.lyafs.com\/ja\/#\/schema\/person\/0a46696ff959c86c3758ad7590adf5c3"},"headline":"Sand Mold and Core Printing: A Buyer&#8217;s Checklist","datePublished":"2026-10-23T10:33:14+00:00","mainEntityOfPage":{"@id":"https:\/\/www.lyafs.com\/tr\/blog\/sand-mold-core-printing-buyers-checklist\/"},"wordCount":1812,"publisher":{"@id":"https:\/\/www.lyafs.com\/ja\/#organization"},"image":{"@id":"https:\/\/www.lyafs.com\/tr\/blog\/sand-mold-core-printing-buyers-checklist\/#primaryimage"},"thumbnailUrl":"https:\/\/www.lyafs.com\/wp-content\/uploads\/2026\/05\/Industrial-Sand-3D-Printer-in-Foundry-1024x768-1.jpg","keywords":["Buyer's Guide","Patternless Casting","Sand 3D Printer"],"articleSection":["Sand 3D Printing"],"inLanguage":"tr"},{"@type":"WebPage","@id":"https:\/\/www.lyafs.com\/tr\/blog\/sand-mold-core-printing-buyers-checklist\/","url":"https:\/\/www.lyafs.com\/tr\/blog\/sand-mold-core-printing-buyers-checklist\/","name":"Sand Mold and Core Printing: Buyer's Checklist","isPartOf":{"@id":"https:\/\/www.lyafs.com\/ja\/#website"},"primaryImageOfPage":{"@id":"https:\/\/www.lyafs.com\/tr\/blog\/sand-mold-core-printing-buyers-checklist\/#primaryimage"},"image":{"@id":"https:\/\/www.lyafs.com\/tr\/blog\/sand-mold-core-printing-buyers-checklist\/#primaryimage"},"thumbnailUrl":"https:\/\/www.lyafs.com\/wp-content\/uploads\/2026\/05\/Industrial-Sand-3D-Printer-in-Foundry-1024x768-1.jpg","datePublished":"2026-10-23T10:33:14+00:00","description":"Six questions decide a sand mold and core printing purchase: volume, largest core, tolerance, sand and binder, post-processing capacity, and process ownership.","breadcrumb":{"@id":"https:\/\/www.lyafs.com\/tr\/blog\/sand-mold-core-printing-buyers-checklist\/#breadcrumb"},"inLanguage":"tr","potentialAction":[{"@type":"ReadAction","target":["https:\/\/www.lyafs.com\/tr\/blog\/sand-mold-core-printing-buyers-checklist\/"]}]},{"@type":"ImageObject","inLanguage":"tr","@id":"https:\/\/www.lyafs.com\/tr\/blog\/sand-mold-core-printing-buyers-checklist\/#primaryimage","url":"https:\/\/www.lyafs.com\/wp-content\/uploads\/2026\/05\/Industrial-Sand-3D-Printer-in-Foundry-1024x768-1.jpg","contentUrl":"https:\/\/www.lyafs.com\/wp-content\/uploads\/2026\/05\/Industrial-Sand-3D-Printer-in-Foundry-1024x768-1.jpg","width":1024,"height":768,"caption":"Industrial sand 3D printer producing a mold in a foundry"},{"@type":"BreadcrumbList","@id":"https:\/\/www.lyafs.com\/tr\/blog\/sand-mold-core-printing-buyers-checklist\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/www.lyafs.com\/tr\/"},{"@type":"ListItem","position":2,"name":"Sand Mold and Core Printing: A Buyer&#8217;s Checklist"}]},{"@type":"WebSite","@id":"https:\/\/www.lyafs.com\/ja\/#website","url":"https:\/\/www.lyafs.com\/ja\/","name":"3DPTEK | AFS","description":"\u00dcnl\u00fc \u00c7inli End\u00fcstriyel S\u0131n\u0131f 3D Bask\u0131 ve H\u0131zl\u0131 D\u00f6k\u00fcm \u00c7\u00f6z\u00fcmleri Sa\u011flay\u0131c\u0131s\u0131","publisher":{"@id":"https:\/\/www.lyafs.com\/ja\/#organization"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/www.lyafs.com\/ja\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"tr"},{"@type":"Organization","@id":"https:\/\/www.lyafs.com\/ja\/#organization","name":"3DPTEK (3D Printing Technology Inc.)","url":"https:\/\/www.lyafs.com\/ja\/","logo":{"@type":"ImageObject","inLanguage":"tr","@id":"https:\/\/www.lyafs.com\/ja\/#\/schema\/logo\/image\/","url":"https:\/\/lyafs.com\/wp-content\/uploads\/2026\/08\/logo-34.png","contentUrl":"https:\/\/lyafs.com\/wp-content\/uploads\/2026\/08\/logo-34.png","width":232,"height":34,"caption":"3DPTEK (3D Printing Technology Inc.)"},"image":{"@id":"https:\/\/www.lyafs.com\/ja\/#\/schema\/logo\/image\/"}},{"@type":"Person","@id":"https:\/\/www.lyafs.com\/ja\/#\/schema\/person\/0a46696ff959c86c3758ad7590adf5c3","name":"Jeff","image":{"@type":"ImageObject","inLanguage":"tr","@id":"https:\/\/www.lyafs.com\/wp-content\/uploads\/2026\/09\/Jeff-150x150.jpg","url":"https:\/\/www.lyafs.com\/wp-content\/uploads\/2026\/09\/Jeff-150x150.jpg","contentUrl":"https:\/\/www.lyafs.com\/wp-content\/uploads\/2026\/09\/Jeff-150x150.jpg","caption":"Jeff"},"description":"30 y\u0131l\u0131 a\u015fk\u0131n katmanl\u0131 \u00fcretim tecr\u00fcbesi ve kendi tesislerimizde \u00e7al\u0131\u015fan 25'ten fazla kum 3D yaz\u0131c\u0131yla, 3DPTEK m\u00fchendislik ekibi teoriden de\u011fil, uygulamal\u0131 \u00fcretim deneyiminden yola \u00e7\u0131karak yaz\u0131yor. Satt\u0131\u011f\u0131m\u0131z \u00fcr\u00fcnleri kendimiz de kullan\u0131yoruz.","sameAs":["https:\/\/www.lyafs.com","https:\/\/www.facebook.com\/profile.php?id=100093519070922","https:\/\/www.linkedin.com\/in\/jeff-wei-56812b244\/"],"url":"https:\/\/www.lyafs.com\/tr\/blog\/author\/test\/"}]}},"_links":{"self":[{"href":"https:\/\/www.lyafs.com\/tr\/wp-json\/wp\/v2\/posts\/8400","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.lyafs.com\/tr\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.lyafs.com\/tr\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.lyafs.com\/tr\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.lyafs.com\/tr\/wp-json\/wp\/v2\/comments?post=8400"}],"version-history":[{"count":1,"href":"https:\/\/www.lyafs.com\/tr\/wp-json\/wp\/v2\/posts\/8400\/revisions"}],"predecessor-version":[{"id":8402,"href":"https:\/\/www.lyafs.com\/tr\/wp-json\/wp\/v2\/posts\/8400\/revisions\/8402"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.lyafs.com\/tr\/wp-json\/wp\/v2\/media\/5849"}],"wp:attachment":[{"href":"https:\/\/www.lyafs.com\/tr\/wp-json\/wp\/v2\/media?parent=8400"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.lyafs.com\/tr\/wp-json\/wp\/v2\/categories?post=8400"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.lyafs.com\/tr\/wp-json\/wp\/v2\/tags?post=8400"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}