الانتقال إلى المحتوى الرئيسي
احصل على عرض أسعار
Precision casting service

الصب الاستثماري الدقيق printed patterns instead of tooling

We print the pattern, build the ceramic shell, pour metal and finish the part. One part minimum, no die required.

Investment casting produced from a 3D printed wax pattern
Ra 3.2-6.3 μm تشطيب السطح
1 part Minimum order quantity
8 Alloy families
30+ years Casting experience

ISO 9001 certified. Ten manufacturing centres, 45+ industrial 3D printers, nine in-house inspection methods, full material certificates with every shipment.

The whole casting chain, in-house

Precision casting covers the lost wax and investment casting family. A pattern is coated in ceramic, the pattern is melted or burned out, and molten metal fills the cavity it leaves. Because the pattern disappears instead of being withdrawn, the mould carries no draft angle and no parting line. That is why this route holds finer detail, thinner walls and tighter tolerances than any other common casting process.

One supplier, one quality system

Your file goes to an SLS wax printer, the pattern is assembled onto a tree, the shell is built and fired, the metal is poured, and the casting is cut off, finished, heat treated, machined and inspected before it ships. Nothing is subcontracted.

See how wax pattern printing works
Pattern

Printed wax patterns, no die

Patterns are printed on our own SLS wax printers. With no injection die to cut, a single part is economic and a design revision costs a reprint rather than a die modification.

Finishing

Machined and inspected before shipping

CNC machining from 3-axis to 5-axis, heat treatment, surface treatment and nine inspection methods, all in-house. You receive finished parts, not raw castings.

Lost wax casting

Lost wax casting without the injection die

Conventional lost wax casting starts with a machined die. Wax is injected into it, and the die sets both the lead time and the minimum order quantity. The die is the bottleneck, not the casting. We remove it by printing the wax pattern directly.

Timing

The first pattern takes days instead of the weeks a machined die needs.

الكمية

One part becomes economic, so validation castings no longer need a tooling budget.

Revisions

Revise the CAD and reprint. A design change stops costing a die modification.

Geometry

Undercuts and internal features that a die cannot release become possible.

Consistency

No die wear means the thousandth pattern matches the first.

Printed wax pattern or wax injection?

Everything downstream is unchanged: the same ceramic shell, the same dewax and burn-out, the same melt and pour, the same finishing. Only the front end changes.

Both are routes we run, so the comparison below is not an argument for one side.

Printed wax pattern compared with conventional wax injection
العاملPrinted wax patternWax injection
Die requiredلانعم
First pattern lead timeالأيامWeeks, for die machining
Cost at 1-20 partsLower overall, no dieDie dominates the cost
Cost at high volumeHigher per patternLower per pattern
Design change costReprint onlyRe-cut or modify the die
Geometric freedomHigh, including undercutsLimited by die release
تشطيب السطحGood, with layer texture to manageVery good by default

When wax injection is the better answer

When your quantity is high and the design is frozen. Once a die is amortised, injected wax is cheaper per pattern, and injection gives a smoother surface than a printed pattern that carries layer texture. The crossover is arithmetic rather than a fixed number: compare the die cost against the per-pattern saving multiplied by the number of patterns you actually expect to use. If that says cut a die, we will tell you.

Precision investment casting with printed patterns

Lead time in investment casting is dominated by tooling. Print the pattern instead and the same foundry process becomes available at quantities and schedules it never supported before. We run three pattern routes, and the right one depends on your quantity and how frozen your design is.

SLS 3D printed wax pattern of a four-cylinder engine block
Printed wax pattern, ready for shell building
Finished aluminium investment castings after shell removal and finishing
Finished investment castings

Direct printed wax

Wax printed on SLS machines and used as the pattern itself. Layer texture is managed by print orientation and pattern finishing, and ash content after burn-out is verified in the shell system rather than assumed from a datasheet.

Printed burnable resin

A resin pattern that burns out of the shell the way wax does. Useful where a part needs a stronger pattern than wax can give it for the dip-and-stucco cycle.

Printed masters for tooling

A durable printed master casts a silicone or low-melt alloy die, which then produces wax conventionally. The bridge between one-off printing and a full steel die.

One honest caveat about precision

What makes investment casting precise is the ceramic shell and the lost-pattern process, not the pattern route. A printed wax pattern does not make the shell more accurate or the alloy shrink less. If a part needs a tighter tolerance than the process can hold, the answer is machining, not printing. What printing removes is tooling-introduced error: die shrinkage, parting line flash, ejection marks and die wear. The first part and every part after it sit closer to the design file.

The printers behind every pattern

We do not buy these machines. 3DPTEK designs, builds and operates the 20+ SLS wax printers that make our patterns, and formulates the wax that goes into them. That is why pattern accuracy holds at ±0.1 mm and why we can quote a build envelope rather than a guess.

LaserCore-6000 SLS wax and sand 3D printer
LaserCore-6000
LaserCore-5300 SLS wax and sand 3D printer
LaserCore-5300
  • LaserCore-6000

    Build 1,050 × 1,050 × 650 mm CO2 120 W Largest SLS build for wax patterns

  • LaserCore-5300

    Build 700 × 700 × 500 mm 55 W / 120 W 150-400 cm³/h Sand and wax dual use

  • AFS-500

    Build 500 × 500 × 500 mm CO2 55 W / 120 W 80-200 cm³/h

  • Multi-part assembly

    Patterns up to 1,400 mm in length Layer thickness 0.08-0.35 mm Ash content under 0.05%

See the full wax printer range
20+SLS wax printers in production
320+Patents in 3D printing
30+In-house wax and binder formulations
±0.1 ممPrinted pattern accuracy

Alloys we cast

Eight alloy families and more than 30 in-house material process formulations. If your alloy is not listed, send the specification. The investment casting route accepts the full range, and we will confirm castability before quoting.

Alloy families available for precision and investment casting
عائلة السبائكTypical gradesTypical applications
الفولاذ المقاوم للصدأ304, 316, 17-4PHMarine, chemical, food-grade, pump and valve bodies
Cast steelZG25, ZG35, ZG45Structural parts, heavy equipment, impellers
الحديد الزهرHT200, HT250, QT400-18Machinery and engine blocks
High-temperature alloysInconel 718, HastelloyTurbine components, aerospace, heat-exposed hardware
الألومنيومA356, A357, ZL101, ZL104Automotive, aerospace, marine housings
التيتانيومTi6Al4VAerospace, medical implants, high-performance parts
سبائك النحاسBrass, bronze, Cu-NiElectrical, marine, architectural and art castings
المغنيسيومAZ91D, AM60Lightweight automotive and electronics housings

Which casting process fits your part

Precision casting is one of several processes we run across ten manufacturing centres. If it is not the right answer for your part, we will quote the one that is.

For the full trade-off between routes, see sand 3D printing vs investment casting, the investment casting and 3D printing guide, or the rapid casting service.

Investment and lost wax casting
Complex, thin-walled parts with fine surface detail, in stainless steel and superalloys. Gives the finest finish and the tightest tolerance of the casting routes.
Sand casting with printed moulds
Large and heavy parts at low to medium volume, plus tooling-free prototypes. Coarser finish and wider tolerance, at a lower cost per kilogram.
Gravity and low-pressure casting
Aluminium structural parts, cylinder heads and pressure-tight components, where density control matters more than surface detail.

Precision casting or another route?

القدرة

التفاوتات المسموح بها ونوعية تشطيب الأسطح

Tolerance in investment casting is set by the shell system, the alloy and the part geometry, not by how the pattern was produced. These are the values we work to. Confirm your critical dimensions in the RFQ and we will state what is achievable for your specific part.

Ra 3.2-6.3 μm تشطيب السطح
±0.3 مم As-cast dimensional accuracy
1 part Minimum order quantity
3-7 days First article delivery, business days

Two accuracy figures, two different things

±0.1 mm is the accuracy of the printed wax pattern as it leaves the printer. ±0.3 mm is the as-cast tolerance of the finished part, measured after shell building, pouring and cooling. The casting step is what consumes the difference, so quoting the pattern figure as a part tolerance would be wrong. Where your drawing needs tighter than as-cast, we hold it by machining the critical features.

  • Pattern production SLS printed, no die
  • Tooling required لا شيء
  • Machining 3-axis to 5-axis CNC
  • المعالجة الحرارية In-house
  • Part envelope Confirmed per drawing
  • Minimum wall thickness Confirmed per drawing

Industries we cast for

From single prototypes to serial production, in alloys that sand casting cannot hold detail in and die casting cannot run at all.

Precision investment cast aircraft engine impellers

الفضاء

Turbine housings, impellers and structural brackets in high-temperature alloys and titanium, with full traceability and non-destructive testing on every batch.

Investment cast pump and valve bodies in stainless steel and bronze

Marine, pumps and valves

Impellers, volutes and valve bodies in stainless steel, bronze and duplex alloys, with pressure-tight testing included.

Investment cast engine cylinder head and motor housing in aluminium alloy

Automotive and motorcycle

Cylinder heads, motor housings and turbocharger components in aluminium and cast iron, from validation parts to serial supply.

Nine inspection gates before shipping

Every casting passes multiple inspection gates before it ships. Nothing is subcontracted, and full material certificates and inspection reports travel with each shipment.

Inspection we run in-house

RT

X-Ray

Internal defect detection for safety-critical components.

CMM

Coordinate measurement

Dimensional verification against the CAD model.

OES

Spectrographic analysis

Alloy composition verified on every heat before pouring.

UT

Ultrasonic testing

Sub-surface flaw detection on heavy sections.

PT

Dye penetrant

Surface crack detection with fluorescent penetrant.

MT

Magnetic particle

Surface and near-surface flaws in ferromagnetic parts.

HB / HRC

Hardness testing

Brinell, Rockwell and Vickers across production batches.

ثلاثي الأبعاد

Scan-to-CAD comparison

Full scan comparison for complex free-form geometry.

Recent precision casting work

Three recent jobs, all delivered with printed tooling rather than a machined die.

Large thin-walled cast steel impeller produced with a printed shell and sand core

Large thin-walled impeller in cast steel

A thin-walled blade structure formed in one piece, holding consistent forming and surface quality better than the traditional route on a compressed schedule.

Large thin-walled cast steel volute produced by 3D printed moulds

Large thin-walled volute, GLH-5

A large volute casing formed in a single piece, holding dimensional accuracy and surface quality above the traditional route.

Aluminium motor housing castings in ZL101A delivered for vehicle testing

Motor housing in ZL101A

40 sets of finished aluminium motor housings delivered in 40 days, ready for vehicle installation and road testing.

Precision casting questions

ما الفرق بين الصب الدقيق، والصب بالشمع المفقود، والصب بالقالب المعدني؟

وهي تصف نفس مجموعة العمليات. يُعرف «الصب بالاستثمار» و«الصب بالشمع المفقود» بالاسمين المعمول بهما لهذه العملية نفسها: حيث يتم طلاء نموذج بالسيراميك، ثم يُذوب النموذج أو يُحرق، ليملأ المعدن التجويف. أما «الصب الدقيق» فهو المصطلح التجاري المستخدم للإشارة إلى القطع المصنوعة بهذه الطريقة، لأن هذه العملية تُختار عندما تكون التفاصيل الدقيقة والتفاوتات الضيقة ذات أهمية. نستخدم هذه المصطلحات الثلاثة بالتبادل، وسنخبرك بالطريقة التي نوصي بها لتصنيع القالب الخاص بقطعتك.

ما هي الكمية الدنيا للطلب في مجال الصب الدقيق؟

قطعة واحدة. ونظرًا لأننا نقوم بطباعة النموذج الشمعي بدلاً من قطع قالب الحقن، فلا توجد أدوات يتعين استهلاكها ولا حد أدنى للكمية. وتخضع القطع الفردية المخصصة للاختبار، والدفعات الصغيرة المخصصة للتشغيل التجريبي، والإنتاج التسلسلي، جميعها لنفس العملية.

هل يمكنكم طباعة أنماط ثلاثية الأبعاد لأغراض الصب بالقالب؟

نعم. هذه هي الطريقة المعتادة التي نتبعها. نقوم بطباعة النماذج الشمعية على آلات SLS الخاصة بنا، ثم نبني الغلاف الخزفي حولها، ونقوم بالصب بالطريقة التقليدية. كما نستخدم النماذج المطبوعة من الراتنج القابل للحرق والنماذج الرئيسية المطبوعة لتصنيع القوالب بسرعة عندما تكون الكمية أكبر من أن تُطبع مرة واحدة، ولكنها أقل من أن تستدعي استخدام قالب فولاذي.

هل تساهم الطباعة ثلاثية الأبعاد في تحسين تفاوتات الدقة في عملية الصب؟

إنها تحسّن الدقة التي تحققها على القطعة الفعلية، لأنها تزيل الأخطاء الناتجة عن الأدوات: فلا يوجد انكماش في القالب يتعين تعويضه، ولا وجود لبروز على خط الفصل، ولا تآكل في القالب، وبالتالي فإن النموذج الألف يتطابق مع النموذج الأول. كما أنه لا يرفع الحد الأقصى للعملية. يتم تحديد التفاوت المسموح به في الصب بالاستثمار من خلال الغلاف الخزفي والسبائك، وليس من خلال مسار النموذج. وإذا كانت هناك ميزة تحتاج إلى دقة أكبر مما تسمح به العملية، فإن الحل هو التصنيع الآلي.

ما هي المدة الزمنية اللازمة لتصنيع قطعة مصبوبة بدقة؟

تستغرق عملية تسليم القطعة الأولى عادةً من 3 إلى 7 أيام عمل. ويقضي مسار النماذج تمامًا على المدة الزمنية اللازمة لتصنيع القالب: فالنموذج الأول يستغرق أيامًا بدلاً من الأسابيع التي يستغرقها القالب المصنوع آليًّا. وقد تؤدي الأجزاء الأكبر حجمًا أو عمليات التصنيع الإضافية أو السبائك الخاصة إلى إطالة هذه المدة، ونقوم بتأكيد الجدول الزمني مع عرض الأسعار.

ما هي السبائك التي يمكن صبها بطريقة الصب الاستثماري؟

ثماني مجموعات من السبائك: الفولاذ المقاوم للصدأ (304، 316، 17-4PH)، الفولاذ المصبوب (ZG25 إلى ZG45)، الحديد المصبوب (HT200، HT250، QT400-18)، وسبائك درجات الحرارة العالية (إنكونيل 718، هاستيلوي)، والألومنيوم (A356، A357، ZL101، ZL104)، التيتانيوم (Ti6Al4V)، سبائك النحاس (النحاس الأصفر، البرونز، Cu-Ni) والمغنيسيوم (AZ91D، AM60). تم تطوير أكثر من 30 صيغة معالجة للمواد داخليًّا. أرسلوا مواصفاتكم وسنقوم بالتحقق من قابلية الصب قبل تقديم عرض الأسعار.

هل تتولون أعمال التصنيع الآلي والمعالجة الحرارية والفحص؟

نعم، كل ذلك يتم داخل الشركة: الصب، والتصنيع باستخدام الحاسب الآلي (CNC) من 3 محاور إلى 5 محاور، والمعالجة الحرارية، ومعالجة الأسطح مثل الأكسدة الأنودية، والطلاء المعدني، والطلاء بالدهان، بالإضافة إلى تسع طرق للفحص تشمل الأشعة السينية، وقياس الإحداثيات، والتحليل الطيفي، والموجات فوق الصوتية، واختبار تغلغل الصبغة، واختبار الجسيمات المغناطيسية، واختبار الصلابة، والمسح ثلاثي الأبعاد. ستتلقى قطعًا جاهزة للتجميع، وليس قطعًا مصبوبة خام.

When is wax injection a better choice than printing?

When your quantity is high and the design is frozen. Once an injection die is amortised, injected wax is cheaper per pattern, and injection gives a smoother surface by default than a printed pattern that carries layer texture. The crossover is arithmetic rather than a fixed number: compare the die cost against the per-pattern saving multiplied by the number of patterns you actually expect to use. We run both routes, so the recommendation you get from us is not an argument for one side.

Send a drawing, get a process recommendation

Upload your 3D model with the alloy, quantity and deadline. Our engineers review it within 24 hours and come back with the pattern route, the alloy and a price. That includes telling you when a different casting process suits your part better.