3DPTEK-J400P — Production-Scale Binder Jetting for Metal and Ceramic Parts
When your R&D phase is done and you are ready to produce — the J400P delivers. 380 × 380 × 300 mm build volume, 3 or 6 high-resolution printheads, and up to 3.6 L/h (metal) or 5.3 L/h (ceramic) throughput. Print MIM-ready metal and ceramic parts at volumes that make traditional tooling look slow and expensive.

Metal Binder Jetting: The Production Technology Between Prototype and Mass Manufacturing
There are three ways to make metal parts at scale. Only one eliminates tooling without sacrificing throughput.
SLM / DMLS
Best for Pilot & Mid-Volume
- Complex geometries
- No tooling
- Laser traces every part — slow at batch
- الهياكل الداعمة المطلوبة
- High per-part cost at volume
Binder Jetting (J400P)
Your Production Bridge
- No tooling — print from CAD
- سرعة الطباعة بالنفث الحبر — طباعة الطبقات بأكملها دفعة واحدة
- لا توجد هياكل داعمة — تعشيش كثيف
- Uses your existing MIM sintering line
- 50× faster than SLM at scale, ~1/5 the cost
MIM (Traditional)
Established at 100K+ Volume
- Lowest per-part cost at 100K+
- Established quality standards
- Tooling: weeks per mold, costly per part family
- Design changes = new mold
- 40–50% binder limits part size
The J400P replaces only the injection molding step. Your debinding and sintering furnaces, your material certifications, your QC procedures — they all stay the same. This is not a rip-and-replace. It is a drop-in upgrade to the front of your existing MIM line.
تخطَّ مرحلة تصنيع القوالب باستخدام تقنية MIM. وانتقل مباشرةً إلى الأجزاء المُتلبَّدة.
Traditional MIM requires a dedicated mold for every part design — weeks of fabrication, significant tooling cost, and zero flexibility when the design changes. The J400P eliminates the mold entirely.
المادة الرابطة 15% مقارنةً بـ 40–50% الخاصة بتقنية MIM
Less binder means larger parts can print and sinter without cracking. MIM is limited to small, thin-walled components; the J400P handles parts MIM cannot — while still feeding your existing sintering line.
عدم الحاجة إلى أي تعديلات على القوالب
Test five design variants in a single build. In MIM, that is five molds. On the J400P, it is one print job. Design feedback in days, not months.
Drop-in to Your MIM Line
The J400P replaces only the injection step. Your debinding furnace, sintering furnace, and post-processing stations continue operating exactly as they do today. No re-certification, no process requalification.
±0.1 mm Accuracy at 1200 dpi
High-density powder spreading and 1200 dpi inkjet resolution deliver the precision MIM, mold and tooling customers demand — including fine features and thin walls.
كيفية العمل: من ملف CAD إلى القطعة المعدنية النهائية
Metal binder jetting in 7 steps — the J400P is your bridge from R&D parameters to pilot production volumes.
التصميم باستخدام برنامج CAD
Create or import your 3D model. Export as STL/3MF. Standard CAD formats — no proprietary file types.
التقطيع والإعداد
AFSWin3DP-L software slices the model. Define binder saturation, layer thickness and print strategy.
الطباعة بتقنية رش المادة الرابطة
Powder spreader deposits a uniform layer. Multi-nozzle inkjet head binds at up to 3.6 L/h across 380 × 380 mm.
الجزء الأخضر من Cure
Printed "green" parts are cured to harden the binder. The build chamber handles full 300 mm height.
إلغاء الربط
Thermal or solvent debinding removes the binder. Compatible with standard MIM debinding equipment.
سينتر
High-temperature furnace fuses metal particles to 98%+ density. Shrinkage is uniform and compensated in software.
قطعة معدنية جاهزة
Production-ready component. Optional: CNC finishing, polishing, heat treatment per application spec.
المواصفات الفنية
المعلمات الأساسية. تتوفر ورقة البيانات الكاملة عند الطلب.
المعلمة | القيمة |
|---|---|
حجم الهيكل (الطول × العرض × الارتفاع) | 380 × 380 × 300 ملم |
أبعاد الخزان (الطول × العرض × الارتفاع) | 400 × 400 × 310 mm |
دقة رأس الطباعة | 400 / 800 / 1200 dpi (metal); 400 dpi (SiC) |
سماكة الطبقة | 0.03–0.2 mm (metal); 0.1–0.3 mm (ceramic) |
Max. Print Speed | 3.6 L/h (metal); 5.3 L/h (ceramic) |
دقة التشكيل | ±0.1 مم |
كثافة الجزء الأخضر | ≈67% |
عدد الفوهات | 3 or 6 (field-configurable) |
المواد | 304/316L, Copper Alloy, High-Temp Alloy, Tungsten Alloy, SiC |
Post-Processing | Curing → Debinding → Sintering |
برنامج التحكم | AFSWin3DP-L الإصدار 1.0 |
أبعاد المعدات | 2,470 × 1,730 × 2,400 mm |
وزن المعدات | ≈2.5 t |

Dual-Platform Materials: Metal & Ceramic
The J400P is one of the few systems in its class that switches between metal and ceramic printing — with over 30 validated material process formulas and 20+ binder formulations in 5 series.
الفولاذ المقاوم للصدأ
SS304، SS316L، SS420، 17-4PH — للاستخدامات الطبية، وتجهيز الأغذية، والهندسة العامة. كثافة متكلسة 98%+ باستخدام مواد رابطة WU08/SU06.
سبائك التيتانيوم
TC4 (Ti-6Al-4V) — مجال الفضاء والطيران والطب الحيوي. عملية تلبيد نظيفة باستخدام مادة رابطة WU08 منخفضة المخلفات.
النحاس وسبائكه
CuSn10، النحاس النقي — إدارة الحرارة والإلكترونيات. مادة ربط مذابة SU06 لضمان الدقة.
السبائك الفائقة
IN625، IN718 — مكونات التوربينات وأنظمة العادم. درجة حرارة التشغيل 650 درجة مئوية فأكثر.
المعادن المقاومة للحرارة
سبائك التنغستن — الحماية من الإشعاع والأثقال الموازنة. التلبيد في الحالة الصلبة.
فولاذ الأدوات
4140، M3/2، H13 — إدخالات التبريد المطابقة للشكل وأدوات القطع. تم توثيق انخفاض زمن الدورة بمقدار 30–40%.
Silicon Carbide
Advanced ceramic for wear parts, armor and semiconductor equipment. CU02 binder at 5.3 L/h throughput.
المؤهلات المخصصة
المواد الخام الخاصة بكم، وعملية التصنيع الخاصة بنا. يستغرق الأمر في المتوسط من 4 إلى 6 أسابيع للوصول إلى المعلمات المعتمدة. تتوفر أكثر من 20 تركيبة من المواد الرابطة.
Production Advantages Over Traditional MIM Tooling
The J400P transforms how MIM factories approach pilot production and small-to-medium batch manufacturing. Eliminate the bottleneck that slows every new part introduction: the mold.
Zero Tooling Required
Traditional MIM requires weeks of fabrication and significant tooling investment. The J400P prints directly from CAD with zero tooling — new part designs go from digital file to green part the same day.
500–5,000 Parts Per Build
Pack hundreds to thousands of small components per print with dense, support-free nesting. Ideal for the batch sizes where MIM tooling amortization becomes uneconomical.
3.6 & 5.3 L/h Dual-Mode
3.6 L/h for high-precision metal parts; 5.3 L/h for ceramic components. Switch materials in under 30 minutes — one printer serves two completely different production workflows.
Iterate Without Penalty
Every design change is a new mold in MIM — and free on the J400P. Modify the CAD file and print again. Test multiple variants in a single build. This is how production engineering should work.
برنامج قطع غيار مجاني
Send us your STL. We print it on a J400P in your chosen material, sinter it, and ship it back with a full process report.

غطاء مفصلي للهواتف الذكية
SS316L | WU08 | 200+ parts per build

SiC Mechanical Seal
Silicon Carbide | CU02 | 5.3 L/h

ملحق التبريد المطابق للشكل
فولاذ الأدوات H13 | SU06 | 35% لدورة أسرع

الغرسة الطبية
التيتانيوم TC4 | WU08 | ISO 13485
مسار التوسع: البحث والتطوير → المرحلة التجريبية → الإنتاج الضخم
All 3DPTEK binder jetting systems share the AFSWin3DP-L platform and binder ecosystem. Parameters transfer seamlessly as you grow.
حالات الاستخدام
نتائج حقيقية تم تحقيقها باستخدام معدات 3DPTEK في الميدان.

أغلفة الأجهزة الإلكترونية 3C
أغطية مفصلات الهواتف الذكية، وعلب الساعات، وحوافها، مطبوعة بدقة 400 نقطة في البوصة مع تشطيب سطحي فائق الجودة — مما يلغي الحاجة إلى عملية التجميع متعددة الخطوات التي تعتمد على تقنيات CNC وMIM.

إدخالات القوالب ذات التبريد المطابق للشكل
طباعة إدخالات قوالب الحقن المزودة بقنوات تبريد مطابقة للشكل مدمجة في فولاذ الأدوات. تم توثيق انخفاض في مدة الدورة يتراوح بين 25 و40%.

أدوات التصنيع وقطع الغيار القابلة للتآكل
أدلة الحفر، والملحقات المقاومة للتآكل، والتركيبات المصنوعة من فولاذ الأدوات — يتم تسليمها في غضون أيام بدلاً من الأسابيع التي تستغرقها الأدوات المصنعة آليًّا أو المصنوعة بتقنية MIM.

المكونات الطبية والمكونات عالية القيمة
مكونات الغرسات المصنوعة من التيتانيوم والأدوات الجراحية المعقدة ذات الهياكل الشبكية الدقيقة — التي يستحيل صبها، لكن طباعتها سهلة للغاية.
الأسئلة الشائعة
Answers to the questions MIM and metal parts manufacturers ask most before investing in a binder jetting system.
The 3DPTEK-J400P supports stainless steels (304/316L/420/17-4PH), titanium alloys (TC4), copper alloys, superalloys (IN625/IN718), tungsten alloys, tool steels (4140/H13) and silicon carbide — over 30 validated material process formulas. Full material parameter sheets are included with every system, and 3DPTEK offers material qualification for custom powder formulations.
The J400P uses only 15% binder versus MIM's 40-50%, so larger parts can be printed and sintered without cracking. It eliminates mold tooling entirely — print directly from CAD, test multiple design variants in a single build, and use your existing MIM debinding and sintering furnaces without process requalification. It is a drop-in upgrade to the front of an existing MIM line.
تتراوح المدة الزمنية القياسية للتسليم بين 8 و12 أسبوعًا من تاريخ تأكيد الطلب. ويشمل كل نظام خدمات التركيب وتدريب المشغلين (لمدة 3-5 أيام في الموقع). ويتولى مهندسو شركة 3DPTEK عمليات تفريغ الصناديق، وتركيب الأجهزة، والمعايرة، والتحقق من جودة الطباعة في النموذج الأول.
نعم. يقدم فريق هندسة التطبيقات في شركة 3DPTEK خدمات تطوير المعلمات، واختيار المواد الرابطة، وتحسين مسار عملية التلبيد، والتحقق من الخصائص الميكانيكية. وقد قمنا بتطوير 5 سلاسل من المواد الرابطة تضم أكثر من 20 تركيبة وأكثر من 30 وصفة لمعالجة المواد. وتتوفر باقات الدعم عن بُعد وفي الموقع.
The J400P features a quick-change build module and dedicated binder circuits. Metal mode uses WU08 (water-based) or SU06 (solvent) binders at 3.6 L/h. Ceramic mode switches to the CU02 binder at 5.3 L/h. Changeover takes under 30 minutes. Both modes share the same AFSWin3DP-L control software with material-specific parameter libraries.
Yes. All process parameters, binder selections and material qualifications developed on the J160R transfer directly to the J400P. 3DPTEK offers trade-in programs and package pricing for customers scaling from R&D to pilot production. The same AFSWin3DP-L software and binder formulations are used across all BJ platforms.
قارن مع طابعات ثلاثية الأبعاد معدنية أخرى
للحصول على حجم تصنيع مختلف أو مجموعة مواد مختلفة، قارن بين أنظمة المعادن التالية: 3DPTEK J160R, 3DPTEK J800P, AFS-M120. أو تصفح النسخة الكاملة طابعات ثلاثية الأبعاد المعدنية النطاق.
